How to Build a Time-Lapse Controller to Photograph Growing Plants

A grid of twelve images shows the blooming sequence of a pink flower against a black background. The top row starts with a closed bud, gradually opening petal by petal in the subsequent rows, until fully bloomed in the last row. Green leaves frame the flower.
A succulent blooms over the course of several days.

This article is about how to make a time-lapse system that controls the lighting conditions and triggers the camera shutter for time-lapse plants.

Time-lapse photography is an area of photography where images are taken every few minutes – here to capture the motion of growing plants. I have been using these techniques for over 30 years. First running 16 mm Bolex cameras before graduating to 35 mm Mitchel cameras and eventually digital cameras. For each camera system, I had to build dedicated time-lapse controllers. Each camera system had its own unique challenges to overcome. Problems of stability of exposures over long durations are now solved with highly stable rolling shutters. The stability of light sources is not an issue with modern LED lights.

The reason to make these relatively complex time-lapse systems is to control three things – the camera shutter, the grow lights for the plants, and the photo light for the exposure. To grow plants over long periods of time requires a grow light that stays on for 12 to 18 hours a day. The typical exposure cycle involves the grow light turning off, the photo light turning on and the camera taking an exposure, then the photo light turns off and the grow light turns back on.

The use of modern LED lights greatly simplifies the process.

Time-lapse control systems are used by so few people that there is currently no manufacturer of this equipment so the few people that photograph in this area typically make their own equipment. Although it is common for cameras to have built-in intervalometers (time-lapse controllers) the cameras cannot control grow lights or photo lights.

The Arduino code here uses a Real Time Clock (RTC) that keeps track of the time of day for a few years until the internal battery runs out. The RTC circuit uses special Arduino code to set the clock time.

The process for setting the RTC is quite simple and well described on the Adafruit website that manufactures the RTC.

The real time clock allows the grow light to turn on at a specific time and turn off at a set time.

I run the plant grow light from 2 am to 8 pm which is an on time of 18 hours which is quite common for plants in the growing phase of their life. This time can be changed to simulate fall or spring sunlight.

The Arduino controller turns off the grow light before each exposure and turns on a photo light. To control these large voltages and currents a special device is used – a solid state relay (SSR) is used. The SSR is an electronic switching device that switches on or off when an external voltage of 5 volts is applied across its control terminals. The SSR serves the same function as an electromechanical relay, but solid-state electronics contain no moving parts, have a longer operational lifetime, and are much faster than a mechanical relay. For this controller, I used a CRYDOM 120v 10A Solid State Relay. Many similar units are widely available on the internet and the critical part is that the SSR can be controlled with the 5-volt output from the Arduino. The control pins in this circuit (pin 11 and Pin 12) have a 10kilo ohm pull-down resistor attached to the pins. This resistor allows any residual voltage to flow to ground and keeps the SSR control pins in the correct logic state. On is +5 volts while off is zero volts.

Diagram showing an Arduino-driven solid state relay setup for controlling a wall outlet. The Arduino pin 11 connects to the relay's input through a resistor and an LED. The relay's output connects to the wall outlet's hot, neutral, and ground terminals.
The connection schematic for the SSR.

There are also two manual switches (switch A and Switch B) attached to the SSR which allow the relays to be manually controlled. This allows the photo light to be turned on to allow for focus and exposure settings, the second manual switch turns on the grow light to make sure it is operating correctly. I mounted the SSR units to blocks of aluminum to help with cooling. Even after running for many hours, the SSR stayed cool.

There are also two LED lights attached to pins 5 and 8 which show the state of the controller.

Data about the current state of the photo shoot is displayed on the Adafruit 12C/SPI LCD Backpack – this is a modified LCD display that is quite easy to use and only requires 4 wires to run. This is a big improvement over the old displays that took over 10 pins to run. Like several of the other components here, this screen is also available from Adafruit.com

If you decide to wire up this circuit make sure you know what you are doing. The SSR handles wall current that will give you a serious shock if you wire wrong or put your fingers in the wrong place.

A schematic diagram shows an Arduino microcontroller connected to a real-time clock module and an Adafruit LCD. It also includes connections to solid-state relays for controlling grow lights and photo lights linked to wall outlets. Two switches are integrated into the circuit.
The time-lapse control schematic.

The finished circuit was placed in a plastic box mainly to keep wires in place.

My photo light of choice is the Godox SL60W which uses a 60-watt daylight-balanced LED with an internal cooling fan. This is an incredibly well-built light that has no measurable variation in brightness. The grow light can be any grow light that you like, over the years I have gone through a number of them but currently use a 1200-watt unit suspended about two feet above the plants.

/*
Time-LapsePlants2024advanced-V2.ino
Ted Kinsman [email protected]
June 2024 update
- includes LCD display
-timer to show next event
-exposure (EXP=) counter
Turns on and off a SSR (Solid State Relay) on pin 12 (grow Light)
Turns on and off a SSR (Solid State Relay) on pin 11 photo LED light
A camera on pin 9.
Test LED on pin 8

NOTE: the ON cycle of the grow light needs to be between 0 hours and 24 hours.
it cannot cross midnight – this issue is due to math dealing with the reset
of the clock at midnight

*/
//initialize the liquid crystal library
//the first parameter is the I2C address
//the second parameter is how many rows are on your screen
//the third parameter is how many columns are on your screen

#include //allows use of the SDA and SCL lines for the three wire liquid crystal display
#include // A library for I2C LCD displays
#include // DS3231 library for the real time clock chip
#include //time library
RTClib myRTC; //name the real time clock for the code
LiquidCrystal_I2C lcd(0x27,20,4); // set the LCD address to 0x27 for a 16 chars and 2 line display

// constants won’t change. Used here to set a pin number:
const int GrowLightOn = 2; //(6AM) turn Grow light on in 24 hour time
const int GrowLightOff = 20; // (6pm)turn Grow light off at 18:00 in 24 hour time
const int LEDB = 5; //test LED

const int GrowLight = 11; // the number of the grow light on pin 11 pin
const int PhotoLight = 12; // Photo light on pin 12
const int Camera = 9; // Pin 9 controls the camera shutter
const int LEDA = 8; //Test LED to show the camera shutter is running on pin 8
long int n = 0; //counter for keeping track of the number of exposures
long int K = 0; //counter for keeping track of the seconds to next exposures
int CameraShutter = 100; //time the camera shutter is pulsed to trigger on in milliseconds
long int PhotoWaitTimeSEC = 180; //time between camera exposures in Seconds
long int PhotoWaitTimeMillSec = 0; // a variable to track milliseconds for wait time
long int ExposureTimeSEC = 1; //exposure in seconds (time to keep photo light on for)
int PhotoLightOn= 1000; //Maybe use this variable ???time to keep photo light on //for.

void setup() { //line below is only run once as setup

lcd.init(); // initialize the lcd
// Print a message to the LCD.
lcd.backlight();

Serial.begin(9600); //turn on serial com interface
Wire.begin(); // the Arduino is ready to send and receive data over the I2C bus.
// this command is used to send data to the LCD display
pinMode(GrowLight, OUTPUT); //GrowLight is an output for Solid state relay
pinMode(PhotoLight, OUTPUT); //PhotoLight is an output for Solid state relay
pinMode(Camera, OUTPUT); //Camera controls the camera shutter and is also an output
pinMode(LEDA, OUTPUT); //test led A is an output to show if the shutter has been triggered (pin 8)
pinMode(LEDB, OUTPUT); //test led B is an output to show if system is waiting (pin 5)

PhotoWaitTimeMillSec = PhotoWaitTimeSEC*1000;
//changes wait time from seconds to milliseconds

ExposureTimeSEC = ExposureTimeSEC*1000; //convert from seconds to milliseconds
delay (1000); // wait for all the electronics to warm up.
}

void loop() {

digitalWrite (GrowLight, HIGH); //turn on grow light
K = PhotoWaitTimeSEC; // counter to record seconds on LCD screen

DateTime now = myRTC.now();
//send the following info to the serial port
Serial.print(“PhotoWaitTimeSEC = “);
Serial.print(PhotoWaitTimeSEC);
Serial.println (” msec”);
Serial.print(“ExposureTimeSEC = “);
Serial.print(ExposureTimeSEC);
Serial.println (” msec”);

Serial.print(“Current Time = “);
Serial.print(now.hour(), DEC);
Serial.print(‘:’);
Serial.print(now.minute(), DEC);
Serial.print(‘:’);
Serial.print(now.second(), DEC);
Serial.println();

//code below controls the grow light by a solid state relay controlled by pin 11
if((now.hour() >=GrowLightOn) && (now.hour() 0){
//lcd.setCursor(1,11);
//lcd.clear();
lcd.setCursor(0,0);
lcd.print(“Wait=”);
lcd.print(PhotoWaitTimeSEC);
lcd.print(” Sec.”);
lcd.setCursor(0,1);
lcd.print(” “); //one way to clear values from bottom line
lcd.setCursor(0,1);
lcd.print(“EXP=”);
lcd.print (n); //send image number to LCD screen
lcd.print(” NXT=”);
lcd.print (K); //send time sec to next image to LCD screen
delay(1000);
K=(K-1);
}
}

A sequence of images showing the blooming process of a yellow St. John's Wort flower. The first image shows the flower as a closed bud, and in each subsequent image, the flower gradually opens, revealing its yellow petals and numerous stamens.
A St. John’s-wort blooms over the course of 30 hrs.

Time-lapse plant photography is never a sure thing. Even after all these years, I calculate only one out of three sequences turns out the way I want. Practice, practice, practice is the key to success.

The design can be simplified by using electrical outlet boxes mounted directly to the controller. Future systems will have the wait time and grow lights adjusted from the controller.

I hope you enjoyed this little article and decide to explore the world of time-lapse plant photography for yourself.

There are not very many books on time-lapse plant photography, but John Ott’s book My Ivory Cellar: The Story of Time-Lapse Photography by Twentieth Century Press 1958 is quite good and changed the direction of my photography as a young man.

A time-lapse sequence showing the stages of a sunflower seed sprouting from the soil. The green stem emerges and grows taller, with the seed casing splitting open and beginning to shed. The background is dark, moist soil.
One of my favorite topics – sunflowers
A grid of nine images showcases the blooming process of a purple water lily against a black background. The top row features the bud starting to open, the middle row displays the flower further blossoming, and the bottom row shows the flower in full bloom.
Blue water lilies – one shot every 5 minutes for this montage.

FOLLOW US ON GOOGLE NEWS

Read original article here

Denial of responsibility! Todays Chronic is an automatic aggregator of the all world’s media. In each content, the hyperlink to the primary source is specified. All trademarks belong to their rightful owners, all materials to their authors. If you are the owner of the content and do not want us to publish your materials, please contact us by email – todayschronic.com. The content will be deleted within 24 hours.

Leave a Comment